Відео

Will these fit a ls3?

I’ve got a 2001 C5 and it’s an amazing car. Corvettes are just amazing cars for daily driving, and have some fun every once in a while corvettes are all around just great cars and can be good daily drivers

Thanks, bro

How much does the top weigh?

reminds me of "how to pick up a duck" and exactly what i was looking for

Thank you for that Sir.. :)

which alternator did you use and did it hold up well?

This needs to be done on my 2007 C6,because the 90 has a small Crack. The shop says that they have to remove way more parts than you did and charge me a shit ton of money! I got a lot of good information watching you perform this task. I am impressed! Great job and thank you for your video. Keep your videos coming.

Funny how no one gets into a '57 Chevy and complains about the interior but every you tuber complains about the interior of a 16 year old Vette. Its not a 2024.

You can straighten it also by clamping in a vise and attach other end to a drill snd spin it. It will straighten right out.

My dream car. And f****ing EU will destroys my dreams😢

Drew Man thanks a mil. I drive a 2000 c5 M6 Vette. As usual getting the "LOW FEUL" light w/DIC (Code :P01431), which indicates pass. side fuel sending sensor prob. On this model I was told that I could access the sending unit by un-bolting it from the tank & removing it w/o dropping the fuel tank. I was told this side has just the level sensor plus other components. Have u a vid. on doing the passenger side of the '97-'04 c5 cars? Also how do I make sure I purchase the correct fuel level sending unit/sensor for my 2000 c5 M6 vette? HELP!! Best.

Great work great video. Thx

Wow! I came for exactly what you just delivered. Delivered with such consideration of my time. New sub here. Thanks!

my 05 does not have problem yet, bring it on!👌😀

Thanks, the owners manual could be better...

🎉excellent instructional video. I like that intake system on the LS2.

J'aime tes vidéos car tu te mets à la portée des gens.

Hey Drew Mann, I've got a C6 2008 Automatic too. I recently installed a "Red Light Bandit" to the accelerator harness. There is a hesitation in the acceleration because of the fly by wire system from the manufacturer. The "Red Light Bandit" makes the acceleration instant and exciting. This device plugs in between the accelerator and the main harness under the dash and doesn't affect anything else. Super cool driving experience! Also, "Maguire's Headlight Coating" is a spray that slows down the UV lens hazing damage on the headlights. The Coating lasts about a year then you will need to re-apply it again after sanding off the coating from the previous year. I put some on my C6 last year and will see how long it lasts this coming year. I keep a cover on my C6 when I'm not driving it, so, that may help the lenses stay clear longer. The lenses face upward and so the UV Rays are hitting them constantly. That is what makes the lenses haze over. FYI

Thanks brother!

Great job nice and clean and well describe 👌

Excelente video y explicación, si me funcionó like y suscripción

Won't that fabric scratch it up from flapping in the wind?

....YOU OUGHT TO USE "MONOKOTE", RATHER THAN "CHEAP"(INFERIOR) CLEAR PACKING TAPE!!

IMHO: THAT MINOR "CURVE" IS NOT AN ISSUE, IF YOU CUT A WING THAT IS THINNER THAN THE FACTORY BOARD THICKNESS!... YOU REALLY OUGHT TO USE A STRONGER SPRING, TO TENSION YOUR HOTWIRE!!!... AND, RUN ALL OF YOUR CUTS IN A VERTICAL PLANE, GOING FROM THE BOTTOM OF THE SLAB, TOWARD THE TOP, SO THAT THE RISING HEAT FROM THE WIRE DOES MORE CUTTING, AND SPEEDS UP THE RATE OF CUT... (WITH A BIT LESS DISTORTION), AND, NEVER USE A "FACTORY SURFACE" (CUT ALL EDGES, AROUND THE AIRFOIL)... ALSO, TURN UP THE VOLTAGE, A BIT, SO THAT THE WIRE CUTS FASTER!!... USE A THINNER (SMALLER GAUGE WIRE)... TO GET FASTER, CLEANER CUTS.

What if the trunk doesn't pop?

Very nice video. But could you have chosen a more expensive alternator link? I think not lol

Fantastic job. Ty😊

you did the work in your driveway? Amazing effort, I was afraid to do mine, but after seeing this, I will do it myself instead of going to the dealer. They would probably charge me a $!000 just to diagnose it, lol

your external relay is in parallel with the existing relay circuit. so the fuel pump is still protected by the existing fuse like before.

Hi. Did you have to remove the tunnel plate? Thanks!

I had to find out at a dealer that no Z06 (unless it's a c7) is targa top, I was looking for latches that didn't exist until the salesman came out and said "wrong trim" thank you both for teaching me something

Hello my friend A question.. Alternator c5 can i used on c6 ls2?

thank you for the tutorial! this help so much!

From what I have heard the dealer charges about $5k to do what you did in a few hours. I have done the passenger tank sending unit on C5 before so it can be done just like you did on jack stands. You made it look very easy. Old guys like me dont move as fast as flexible as you do . This was one of the best videos I have seen on You Tube. For as young as you are you are one hell of a good mechanic. Wish my grandsons had your skills none of them have any interest in working on cars. Guess I wont be willing my Corvette to them on my passing.

Fantastic video and a great job with limited tools and lift.....

Simple as that. Thank you Chevrolet

You got exceptional knowledge, self discipline, tools, and communication skills for one so young. The product of exceptionally good parents. Where'd you find C6 compatible wheel ramps?

Appreciate it

I know this us an old video but do you still habe the car and is this fix still working? Thinking bout doing this to mine.

I’ve always had someone help me take mine off. I don’t know why I never thought of doing it the way you showed. This is awesome!! Thanks!!

Can every c6 do this??

Have you got yourself an electric ratchet yet lol

My man is not happy he didn’t have a manual 😂😂 “but that’s fine” hahah I’m dying

nice i was looking into buying one and was thinking i'd always need a second hand when removing/installing.

Most definitely about to do this to my corvette on a nice day😂 just got it like 3-4 days ago

want to come do my driver side?

a large battery cable size wire that you keep calling a ground is actually a positive it's not a ground put a voltmeter to it and check it and see if I am right

Awe man I could have done that job myself. Excellent video Mann

hello, voltage AC or DC, and I want to make foam for cutting